HYDRAULIC IMPACT WRENCH ID07 CE
The ID07 is a high torque impact wrench used for tightening and loosening nuts and screwing lag bolts. It applies impact torque up to 500 ft-lb /675 Nm. Available with friction ring or bolt type retaining socket.
The ID07 is a high torque impact wrench used for tightening and loosening nuts and screwing lag bolts. It applies impact torque up to 500 ft-lb /675 Nm. Available with friction ring or bolt type retaining socket.
Valve with M25 thread and toroidal sealing bottles (not EN144), exit DIN / INT convertible by core with a 232 atm working pressure. Black plastic knob on the left and output for connection to modular manifold.
The ID07 is a high torque impact wrench used to adjust and loosen nuts and bolts. Apply a maximum impact torque of 675 Nm. Available with friction ring or bolt retainer sleeve.
Valve with M25 thread and toroidal sealing bottles (not EN144), exit DIN / INT convertible by core with a 232 atm working pressure. Black plastic knob on the right and output for connection to modular manifold. Matte black finish, designed for special forces that avoids glare and camouflages the diver's silhouette.
Stanley hydraulic impact wrenches for underwater applications are designed to meet the most stringent requirements for underwater screwing. Their rugged design includes an integrated motor and a rugged mechanism for the tough demands of railroad maintenance. The weight ratio -The power of this equipment has no comparison with an impact wrench of this type on the market.
Valve with M25 thread and toroidal sealing bottles (not EN144), exit DIN / INT convertible by core with a 232 atm working pressure. Black plastic knob on the left and output for connection to modular manifold. Matte black finish, designed for special forces that avoids glare and camouflages the diver's silhouette.
Modular side right-type valves cap, to close the side exit to exit manifold or modular plug.
Modular side Left-type valves cap, to close the side exit to exit manifold or modular plug.
Modular side Right-type valves cap, to close the side exit to exit manifold or modular plug. Matt black finish of the military series.
Modular side Left-type valves cap, to close the side exit to exit manifold or modular plug. Matt black finish of the military series.
Valve with M25 thread and toroidal sealing (not EN144) DIN output with a working pressure of 300 b. Black plastic knob. The valves are shipped with seals and lubricants compatible for oxygen.
The SM20 submersible pump is self-priming and can run dry without damage. It has the capacity to pump 250 gpm (946 lpm) and move solids up to 8 mm in diameter, making it an extremely powerful and reliable pump.
Stanley hydraulic pumps exemplify the sheer power of hydraulic tools. Our SM50 pump releases no less than 500 gallons per minute (1890 bpm) and its small size allows it to fit into an 11 inch deep by 10 inch square (26.7 cm x 25.4 cm) box.
Single valve to old tanks of 3/4 Gas (3/4 NPSM), DIN/INT connection. Hand Wheel Grip in black rubber on lef.
Stanley hydraulic pumps exemplify the sheer power of hydraulic tools. Our SM50 pump discharges no less than 500 gallons per minute (1890 lpm) and its small size allows it to fit into a box 11 inches deep by 10 inches square (26.7 cm x 25.4 cm).
The TP03 and TP08 waste pump lines are a good example of the hydraulic power used to pump liquids containing solids. The TP03 pump provides a discharge capacity of 450 gallons per minute (1688 l / min) and can pump solids up to a diameter of 76 mm (3 in).
Twins valve for 10 or 12 liters in long form cylinders (171 mm diameter). With metric M25x2 EN144 thread . Manifold connection with isolation valve.
The TP03 and TP08 waste pump lines are a good example of the hydraulic power used to pump liquids containing solids. The TP08 has a discharge capacity of 800 gpm (3028 lpm) and can pump solids up to 4 inches (102 mm) in diameter.
Twins valve for 18 liters long cylinders (216 mm diameter). With metric thread M 25x2 EN144. Manifold connection without isolating valve
Twins valve for 10 or 12 liters in long form cylinders (171 mm diameter). With metric M25x2 EN144 thread . Manifold connection with isolation valve. Matt black finish, designed for special forces that avoids glare and camouflages the diver's silhouette.
Manifold with isolation valve for twins mounting. Different measures depending on the cylinders of the set: 171 mm, 180 mm (aluminium) and 203 mm
Manifold with isolation valve for twins mounting. 171 mm for 10/12 long twins. Matt black finish of the military series.
Without isolation valve manifold for mounting twins. Different measures depending on thecylinders of the set: 171 mm for 10/12 liters long twins, 203 mm for 12/15 liters twins
Tds nitrox identification sticker to put on bottles Nitrox tanks and make a perfect identification and distinction from other bottles. Dimensions 60 cm x 15 cm