Cookie preferences
LATEST NEWS
CO23 UNDERWATER CUT-OFF SAW
The Stanley Hidraulica Submarine CO23 Circular Saw was designed for use underwater, but it is also a very useful tool on land. The CO23 uses wet or dry abrasive diamond discs, with a standard 10 inch (25.4 cm) diameter for cutting metals or concrete.
450-550-650-750 ET SILENT COMPRESSOR...
Coltri 450-550-650-750 ETS Silent Scuba Diving High Pressure Compressor Threephasic: The SILENT model represents excellence in soundproofing. It has been designed to meet the needs of very intensive uses and when large filling capacities are required. Equipped with 4 front filling connections for high pressure hoses (from 232 to 420 bar), a control panel and an electrical display. They are equipped with a three-phase electric motor and powerful pumping units (450 550 650 750 depending on the specific model).
POWERCOM - MILCOM
The new POWERCOM and MILCOM line takes wireless communication performance to the next level for all your professional diving needs. Its specifically designed rechargeable lithium-ion battery packs more power for longer range
NOVATECH FLASHERS
NOVATECH™ Beacons and Flashers are an integral component of ocean exploration and study. Flashers provide the added insurance of a visual aid with an intense flashing light to assist in recovery missions.
CS06 CHAIN SAW
The Stanley CS06 Underwater Hydraulic Chainsaw features a 15-inch saw and today offers the diver a tool with the highest power-to-weight ratio underwater on the market today.
450-550-650-750 ET OPEN COMPRESSOR (Threephasic)
Coltri 450-550-650-750 ET Open threephasic Commercial Diving High Pressure Compressor: Open meets professional needs that require large charging capacities in hot, poorly ventilated or tropical countries. It is equipped with 4 front filling connections for high pressure hoses, an intuitive control panel and an electric motor. The pumping unit, chosen from the 4 most powerful, is exposed in the rear part of the structure to ensure a better cooling cycle. For longer filter life, the Tornado high pressure dryer is recommended
LP 250 NITROX ROTARY
Coltri LP250 Nitrox ROTARY for Scuba Diving: It consists of an industrial screw compressor that delivers air at a pressure of 10 bar to the Parker® membrane. The percentage of oxygen obtained at the outlet can be adjusted from 32% to 36% thanks to a valve accessible on the front side of the compressor. If connected to a compressor with pumping unit 315 (MCH 16), Nitrox at 32% can be obtained up to a pressure of 232 bar. The oxygen analyzer allows you to check the correct percentage, adjusting it through the appropriate valve.
DUSKY LASER
The Dusky Shark T2 Subsea Line Laser is used when measurements are needed from video images.
NOVATECH RADIO BEACONS
The NOVATECH™ Tracking & Monitoring products allow for recovery insurance in harsh submarine environments.
PROBLENDER 1000 TRIMIX BLENDER
The solution to mix Nitrox, Trimix, Triox and Héliox while emptying B50. Allows to mix any Nitrox, Trimix, Triox and Héliox having a maximal rate of 40% of O2. The technic consists in making Nitrox, Trimix, Triox or Héliox before compressing it by the mean of the compressor. That is why we must not exceed 40% of O2.
SRP PANEL 3 DIVERS IMCA
The FULL DIVING CONTROL SBQ panel is a portable control and monitoring supply system for surface supplied air diving operations for three divers. The system has been designed to supply air from the surface, control the depth of the divers, have communication and visualize the operations of the divers from the surface.
LP 300 NITROX ROTARY
The Coltri LP300 Nitrox ROTARY model consists of an industrial screw compressor that delivers air at a pressure of 12 bar to a membrane that separates nitrogen and oxygen up to a maximum percentage of 40% O2. The enriched air can be compressed at a pressure of 232 bar in combination with a high pressure compressor. The percentage of oxygen obtained at the outlet can be regulated from 22.4% to 40% using a valve directly accessible on top of the compressor. The oxygen analyser allows checking of the correct percentage adjusted by means of the appropriate valve.
PROBLENDER 1000 NITROX BLENDER
The best solution to blend Nitrox while emptying B50 safety. Allows to blend any Nitrox up to 40 % of O2. The technique consists in mixing the Nitrox before passing it through the compressor. It is for this reason that we can not exceed 40 % of O2.
CS11 UNDERWATER CHAIN SAW
The CS11 Underwater Work Circular Saw is designed to cut any type of wooden structure underwater, including bridge piers, docks and jetties. It was created to provide the diver with a very high chain speed to easily cut even the sturdiest posts and pillars.
SRP 2 DIVERS PANEL IMCA
Synergy designed diving SRP's are one of our popular products and have been very well received in the diving industry. Manufactured with a stainless steel frame, 4 x 50 ltr x 200 bar lightweight carbon composite cylinders, all connected to an air management panel and the two diver panels for diver air supply and cylinder charging.
LP 600 NITROX ROTARY
At the top of the Nitrox line, the Coltri LP600 ROTARY system consists of an industrial screw compressor that delivers air at a pressure of 8 bar to a membrane that separates nitrogen and oxygen at atmospheric pressure until Nitrox 40% O2 is obtained and can be compressed at a pressure of 232 bar in combination with a high pressure compressor. The percentage of oxygen obtained at the outlet can be regulated from 22.4% to 40% using a valve directly accessible on top of the compressor. Exclusive to the the Heavy Duty line compressors.
10-FOOT DIVE CONTROL STATION
Synergy designed 10ft containerized dive control cabin with HP cylinder holder and air panel for three divers is one of our best selling products. The air-conditioned insulated container is perfect for land-based marine construction work, especially in hot climates. The self-contained unit only needs one HP compressor kept outside to charge the quads for 24/7 diving operations.
DS11 CHAIN SAW
The DS11 Diamond Chain Saw is designed for cutting concrete underwater. It is suitable for cutting corners without overcuts and can cut walls up to 45 cm thick. Two bar lengths (38 cm and 45 cm) and two different types of chain are available. A minimum of 20 psi of water pressure is required at the saw to cool and lubricate the bar and chain.
FILLING PANEL FOR COMPRESSOR
It has two gauges (one for each pressure) for controlling the load pressure. With its internal pressure regulator, you have the ability to offer dual pressure load (2 outputs and 2 outputs 300 bar to 225 bar).